Creality · Laser Engravers & Cutters
Creality Falcon2 Pro review: the enclosed diode laser most makers should look at first
A fully enclosed 22 W or 40 W diode laser with a 400 × 415 mm bed, camera, exhaust and safety sensors, from $899. Powerful and safe, but focus is manual and setup takes an evening.
Very good
Best for Home workshops and small businesses that want cutting power with an enclosure
List price$1,349
We may earn a commission when you buy through links on this page. It never changes our scores. Learn more
Preview review. Compiled from manufacturer specifications and published information. We will update the scores after hands-on testing.
Our verdict
The Falcon2 Pro puts a strong diode laser inside a proper Class 1 enclosure with camera, exhaust fan and fire sensor. The Gadgeteer called the 40W the best laser engraver they had owned, and store buyers rate it 4.86/5. Focus is manual, the camera is a few millimetres off, and the exhaust hood is tedious to fit. At $1,349 for 40W it is one of the safest ways to get serious cutting power at home.
What we like
- Fully enclosed, FDA Class 1, with lid interlock, fire, tilt and dirty-lens sensors
- 40W cuts plywood, walnut and acrylic quickly; 22W Precise mode for detail
- Large 400 × 415 mm work area
- Built-in camera, exhaust fan, air assist and crumb tray
- Works with LightBurn as well as Creality’s free software
What could be better
- No autofocus: you set focus by hand
- Camera placement was about 5 mm off in The Gadgeteer’s test
- Exhaust hood assembly is tedious; the enclosure leaks a little smoke
- Bigger and more complex to set up than open-frame Falcons
- Cannot be upgraded to the IR-module versions later
Score breakdown
Overall = 35% Power and speed + 25% Results and build + 20% Software and safety + 20% Value. How we test
What is it?
The Falcon2 Pro is Creality’s enclosed version of its popular Falcon2 open-frame laser. It adds a full Class 1 enclosure, a camera, an exhaust fan and a crumb tray around the same 400 × 415 mm work area. It comes in 22W, 40W and 60W versions; we review the 60W separately.
On 31 October 2026 the official store sells the 22W for $899 and the 40W for $1,349. Versions with a 2W infrared module (for bare metal and plastics) cost $1,599 and $1,999. You cannot add the IR module later.
Setting up
The machine arrives mostly built, but the exhaust hood and duct take time. The Gadgeteer found that part tedious, and Tried & True found setup more complex than their previous laser. It is also much larger than the open-frame Falcon2, so measure your bench first.
Focus is manual. There is no autofocus and no crosshair pointer, so you lower the head with the focus block before each job.
Cutting and engraving
The Gadgeteer used the 40W for several weeks:
- Plexiglass and walnut cut cleanly and quickly.
- Stainless steel took colour engraving.
- It made rubber stamps and coasters with good detail.
- Trying a single-pass cut through 38 mm of wood set the wood alight. The fire sensor stopped the job, which is exactly why the enclosure and sensors matter.
The 40W module also has a 22W Precise mode, so you can trade speed for a finer spot on detailed engraving. Some bundles include a separate 1.6W module for very fine work.
Camera and software
The camera lets you place designs on the material on screen. The Gadgeteer needed three runs to calibrate it, and placement was still about 5 mm off. Good enough for coasters, not for engraving exactly on a pre-cut part.
It works with Creality’s free Falcon Design Space, LightBurn (about $60 a year) and LaserGRBL. Most reviewers chose LightBurn.
What owners say
The official store shows 4.86/5 from 49 reviews. Hagensieker’s review found engraving results better than expected. The common complaints are the ones above: manual focus, size, and a slightly leaky enclosure.
Who should not buy it
- Anyone who mostly marks bare metal: get the IR version or a fibre laser.
- Anyone short on space: the A1 Pro is far more compact.
- Anyone who wants autofocus and a smart workflow: look at the Falcon A1 Pro.
vs rivals
- vs Falcon2 Pro 60W ($1,899): about 50% more power for $550 more. Worth it only if you cut thick wood daily.
- vs Falcon A1 Pro ($1,099): smaller bed and 20W, but autofocus and a touchscreen. See Falcon2 Pro vs A1 Pro.
- vs LaserPecker LX2 ($1,499): also enclosed, with a larger 500 × 305 mm bed.
Final thoughts
If you want to cut real material at home without an open laser beam in the room, the Falcon2 Pro 40W is the sensible pick. Budget an evening for setup and learn to focus by hand.
Sources
Full specifications
| Laser | 22W or 40W blue diode (40W has a 22W Precise mode) |
|---|---|
| Work area | 400 × 415 mm |
| Enclosure | Fully enclosed, FDA Class 1 |
| Camera | Built-in, for positioning |
| Safety | Lid interlock, flame, tilt, overheating and dirty-lens sensors |
| Software | Falcon Design Space, LightBurn, LaserGRBL |
| Price | 22W $899 · 40W $1,349 · with 2W IR: $1,599 / $1,999 |
| Released | 2024 |
Ready to buy?
Creality Falcon2 Pro (22W / 40W)
List price $1,349. Prices change often, so check the current deal.
Head-to-head
Creality Falcon2 Pro (22W / 40W) compared
Keep reading
